Underground Warning Tape With Tracer Wire
- Material: PE/OPP laminated film
- Tracer wire: SS304 or SS316
- Wire diameter: 0.4mm, 0.5mm, 0.7mm
- Tape thickness: 100um, 130um, 150um
- Width/length: 75mm-300mm, 100m-500m
- Color/print: APWA colors, custom legends
No products were found matching your selection.
Other Related Products
-
-
Slip Resistant Tape For Stairs
- Regular widths: 25 mm, 50 mm, 100 mm, with custom stair strip sizes
- Colors: black, gray, yellow-black warning, or project colors
- Surface: mineral grit abrasive layer for high-friction shoe contact
- Backing: PVC/PET film, with foil-backed option for textured metal steps
- Adhesive: pressure-sensitive acrylic adhesive with release liner
- Supply format: rolls, pre-cut strips, rounded-corner die cuts
-
Reflective Strips For Sign Posts
- Common Sizes: 2 in, 3 in, 4 in widths
- Colors: Yellow, red/white, yellow/black
- Material: PVC or PET reflective film
- Structure: Glass bead or micro-prismatic
- Adhesive: Pressure-sensitive acrylic backing
- Tested Surfaces: Metal, PVC, plastic bollards
-
Thermoplastic Road Marking Tape
- Typical Thickness: 1.6-2.2mm
- Colors: White, yellow, red, blue, black
- Material: Hot-melt thermoplastic compound
- Reflective Structure: Embedded glass beads
- Installation: Torch heating, compression, cooling
- Uses: Lines, arrows, symbols, crosswalks
-
Non Adhesive Barrier Tape
- Material: PE, LDPE, or HDPE film
- Common Width: 50 mm, 75 mm, 100 mm
- Thickness: 30 um-100 um
- Roll Length: 100 m, 200 m, 300 m, 500 m
- Colors: yellow/black, red/white
- Installation: tying, stapling, nailing, wrapping
-
Reflective Sheeting For Traffic Signs
- Roll size: 1.22 m x 45.7 m
- Width tolerance: +/- 2 mm typical
- Colors: white, yellow, red, blue, green, orange, black
- Structure: PVC, PET, PC, or PMMA-based film
- Adhesive: permanent pressure-sensitive adhesive
- Liner: release paper or film liner
-
Warehouse & Factory Floor Marking Solutions
A reliable tape for warehouse floor marking must do more than create a visible line. It must match the traffic pattern, floor condition, cleaning routine, operating temperature, and future removal plan. This solution is intended for pedestrian walkways, forklift routes, pallet locations, work cells, loading approaches, quarantine zones, and equipment-clearance boundaries. The main risks are weak contact, edge lifting, lateral movement, backing wear, adhesive transfer, and disturbance of an existing floor coating. Selection should therefore be based on the actual surface, traffic action, application pressure, bond-building time, and a representative site trial—not color or thickness alone.
-
DOT Trailer Reflective Tape Requirements: Placement and Installation Guide
DOT trailer reflective tape requirements combine vehicle eligibility, placement dimensions, material identification, optical performance, adhesive behavior, and installation control. This reference applies to pressure-sensitive red-and-white conspicuity sheeting used on qualifying commercial trailers and semitrailers. Regulatory dimensions are mandatory where applicable, while thickness, peel adhesion, holding power, temperature, and weathering values remain grade-specific or project-confirmed. Verify…
-
Detectable Underground Utility Marking Tape
- Common Widths: 2 inch, 3 inch, 6 inch, or project-specific width
- Roll Lengths: 500 ft, 1000 ft, or custom roll length
- Structure: PE or PET film with continuous aluminum foil layer
- Colors: APWA red, yellow, orange, blue, green, purple and custom colors
- Printing: Buried utility legends, 20 inch – 36 inch repeat available
- Use: Direct burial above utility lines before trench backfill
