Underground Warning Tape With Tracer Wire
- Material: PE/OPP laminated film
- Tracer wire: SS304 or SS316
- Wire diameter: 0.4mm, 0.5mm, 0.7mm
- Tape thickness: 100um, 130um, 150um
- Width/length: 75mm-300mm, 100m-500m
- Color/print: APWA colors, custom legends
No products were found matching your selection.
Other Related Products
-
-
Anti Slip Tape For Bathroom Tiles
Common Size: 25 mm, 50 mm, 100 mm widths; custom lengths available
Color: Transparent, translucent white, light gray options
Material: PEVA/PVC textured film with pressure-sensitive acrylic adhesive
Thickness: Approx. 0.45-0.75 mm depending on grade
Adhesive: Waterproof acrylic adhesive compatible with smooth tile surfaces
Use Area: Bathroom tiles, shower floors, bathtub edges, wet ceramic tile areas -
Metal Detectable Foil Tapes
- Common size: 10mm-500mm width, 30m-1000m length
- Color: Silver, red, blue, yellow, or custom surface color
- Material: Aluminum foil, PET, paper, PTFE glass, or laminated film
- Structure: Single coated, double coated, or non-adhesive foil strip
- Thickness: 0.08mm-0.28mm typical total thickness
- Supply:Slit rolls, sample rolls, jumbo rolls, or die-cut pieces
-
Warehouse & Factory Floor Marking Solutions
A reliable tape for warehouse floor marking must do more than create a visible line. It must match the traffic pattern, floor condition, cleaning routine, operating temperature, and future removal plan. This solution is intended for pedestrian walkways, forklift routes, pallet locations, work cells, loading approaches, quarantine zones, and equipment-clearance boundaries. The main risks are weak contact, edge lifting, lateral movement, backing wear, adhesive transfer, and disturbance of an existing floor coating. Selection should therefore be based on the actual surface, traffic action, application pressure, bond-building time, and a representative site trial—not color or thickness alone.
-
DOT Trailer Reflective Tape Requirements: Placement and Installation Guide
DOT trailer reflective tape requirements combine vehicle eligibility, placement dimensions, material identification, optical performance, adhesive behavior, and installation control. This reference applies to pressure-sensitive red-and-white conspicuity sheeting used on qualifying commercial trailers and semitrailers. Regulatory dimensions are mandatory where applicable, while thickness, peel adhesion, holding power, temperature, and weathering values remain grade-specific or project-confirmed. Verify…
-
Industrial Floor Marking Tape
- Material: PVC/vinyl film
- Adhesive: Rubber pressure-sensitive adhesive
- Common widths: 48 mm, 50 mm, 75 mm, 100 mm
- Common colors: Yellow, red, blue, green, white, black, striped
- Roll length: 30 m, 33 m, 50 m, custom length
- Use surface: Clean concrete, epoxy floor, sealed industrial floor
-
Photoluminescent Glow In Dark Film
- Common Size: 1.22 m x 45.7 m roll
- Color: Yellow-green surface
- Material: PVC/PET based film
- Structure: Surface film + photoluminescent layer + adhesive
- Backing: Permanent acrylic adhesive with release liner
- Use: Exit signs, stairs, corridors, route markers
-
Non Adhesive Barrier Tape
- Material: PE, LDPE, or HDPE film
- Common Width: 50 mm, 75 mm, 100 mm
- Thickness: 30 um-100 um
- Roll Length: 100 m, 200 m, 300 m, 500 m
- Colors: yellow/black, red/white
- Installation: tying, stapling, nailing, wrapping
-
Slip Resistant Tape For Stairs
- Regular widths: 25 mm, 50 mm, 100 mm, with custom stair strip sizes
- Colors: black, gray, yellow-black warning, or project colors
- Surface: mineral grit abrasive layer for high-friction shoe contact
- Backing: PVC/PET film, with foil-backed option for textured metal steps
- Adhesive: pressure-sensitive acrylic adhesive with release liner
- Supply format: rolls, pre-cut strips, rounded-corner die cuts
